Spring Sale – 40% off!

Tokenblauser GPSDO

450.00USD

Specifications

Achieve impressive stability for frequency reading.

Use a specialized GPS generator with ultra-accurate and ultra-stable characteristics to calibrate your gear.

Enjoy experimenting with Aurdino-compatible GPSDO built into open-source software.

Four outputs allow you to simultaneously use Tokenblauser GPSDO as a stable test signal and for GPS discipline of multiple devices.

PLL synthesized outputs

Output frequency range

0.16 to 200/350/710 MHz (depending on a PLL type)

Frequency setting

With 1 Hz steps (or very fine tuning with 1 ppt steps)

Auxiliary output

10 MHz

Frequency stability

0.001 ppm or better

Signal levels

3.3V CMOS logic

Output connector

BNC

GNSS antenna type

External, active, 3.3V

GNSS constellations

GPS, Galileo

Dimensions

100mm x 100mm x 25mm (PCB), 105mm x 105mm x 35mm (enclosure)

Accessories inside the box

12V power adapter (EU or US), GPS active antenna, USB cable, User’s manual

Note

Made in EU, Specifications are subject to change without notice

GTIN-13

4820185420440

Close specifications

TI-5000

120.00USD

Where to buy

Specifications

Powerful USB transceiver interface based on high-quality stereo codec IC, for operating phone, CW, and digital modes using a personal computer.

All in one through a single USB port. Ideal interface for FT8 and WSJT modes!

General features

CAT (Computer Aided Transceiver) system, CW keyer (WinKey), Footswitch input, FSK output, Microphone input, PTT and CW outputs, Transceiver audio interface for operating digital modes, voice recording and playback

Computer connection

No external power supply needed, Powered from the USB port (consuming 100 mA maximum), USB (Universal Serial Bus) connector

Transceiver connection

Single 25-pin connector for transceiver cable, Various transceiver models supported

Audio interface

External microphone input with level control, Input/output samplerate: 8 to 48 kHz, Insulated from digital nets, Maximum input/output amplitude is 1V, Recording QSO audio stream, Volume levels are adjusted by the front panel potentiometers

CAT serial port

Baudrate: 300-115200 baud, Electrical compatibility: RS-232, CI-V, TTL or inverted-TTL (Yaesu, Icom, Kenwood, Ten-Tec, Elecraft and JRC transceivers)

PTT/CW outputs

CW output: open collector, Maximum current is 50 mA, PTT output: open collector and TTL-level

FSK output

Baudrate: 45-1200 baud, Open collector output

System requirements

Desktop or laptop computer with USB 1/2/3 compliant port, For Windows 7 and previous versions of Windows only FTDI drivers are required, MacOS/Linux/Windows 2000/XP/2003/Vista/7/8/10 (32- or 64-bit) operating system, No drivers required for systems on Windows 10/MacOS/Linux

Supported software

all other soundcard software!, MixW 2/3/4, MMTTY, MMSSTV, WSJT, WSJT-X, WSPR

Dimensions

200 x 100 x 40 mm

Weight

300 g

Operating temperature

0…40 °C (32…104 °F)

GTIN-13

4820185420167

Note

Specifications are subject to change without notice, Мade in Ukraine

Close specifications

ZERO II

70.00USD

Where to buy

Specifications

1 GHz VNA for embedded applications & perfect device for embedded installation. It used, for example, antenna tuners, transceivers, or power amplifiers as the core of the load-matching circuit.

ZERO II is also useful for:

manufacturers of power equipment HAM radio direction;

developers and manufacturers of devices requiring long-distance packet data transmission using different protocols.

It is capable on:

measures up to 1GHz– Instantly returns R, X, SWR & Return Loss values;

comes factory calibrated;

has USB, UART, I2C, and SPI interfaces use.

Frequency range

0.1 to 1000 MHz

Frequency setting time

20 ms

Return values

Resistance, Reactance (signed), SWR, Return Loss

Output connector

SMA

Output power

-10 dBm

Power

USB or from 3V to 48V through Power port

Operating temperature

0…40 °C (32…104 °F)

Interface

USB, I2C, SPI, UART

Dimensions

30 x 40 x 4 mm (1 x 2 x 0.2 inches)

Weight

30 grams (3 Oz)

Warranty

1 year

Note

Specifications are subject to change without notice, Мade in Ukraine

GTIN-13

4820185420341

Close specifications

REAMP Power Measurement Tool and logger

70.00USD

Where to buy

Specifications

When you want to achieve the longest battery life possible, you need an accurate and reliable power measurement tool.

So REAMP is the best choice for your Ultra-Low Power projects.

REAMP acts as a very stable and accurate power source for Device Under the Test (DUT).

This allows to see even subtle changes in the power consumption profile of the DUT.

Number of measuring channels

Measuring range

Current – 10μA to 1А (1 channel), Voltage – 0V to 5V (2 channels)

Sample rate

10 hZ…10 kHz (10 kHz one channel only)

Measuring results displaying

Average values in digital format, Easy navigation using horizontal and vertical zooming, Instant values graph, Saving data to a log

Power supply

Additional built-in Li-ion battery to be used when current consumption is over 500 mA, PC USB port

Interface

3 languages support (EN, UA, RU), Application software “REAMP Logger”, Operation system Windows 7, Windows 8, Windows 10, USB connection to a PC (USB 2.0, USB 3.0)

Dimensions

67 mm x 57 mm x 27 mm

Operating temperature

0…40 °C (32…104 °F)

Weight

100 g

Warranty

1 year

GTIN-13

4820185420334

Note

Specifications are subject to change without notice, Мade in Ukraine

Close specifications